Jump to content

Wikipedia:Reference desk/Archives/Mathematics/2012 September 27

From Wikipedia, the free encyclopedia
Mathematics desk
< September 26 << Aug | September | Oct >> September 28 >
Welcome to the Wikipedia Mathematics Reference Desk Archives
The page you are currently viewing is an archive page. While you can leave answers for any questions shown below, please ask new questions on one of the current reference desk pages.


September 27

[edit]

mode

[edit]

when calculating a mode, what do you do when 1: there is no number that occurs more then once, and 2: there is a tie between 2 or more numbers (example: 1, 2, 3, 3, 4, 4, 5)? p.s.: are your captchas cap-sensitive? thanks, 70.114.254.43 (talk) 00:51, 27 September 2012 (UTC)[reply]

As for the mode, those are probably situations where the mode is not an appropriate measure of central tendency. It's meant for data where there is a clear mode, like say a (possibly distorted) bell-shaped curve. Therefore, the mode should be either a single value, or perhaps two adjacent values, in which case you could say the mode is midway between the two, so 3.5, in your example. StuRat (talk) 00:57, 27 September 2012 (UTC)[reply]
I don't know for certain if the capcha used when you sign up for a Wikipedia account is case-sensitive, but it would make sense if it were, to make it more difficult for programs to determine. StuRat (talk) 01:00, 27 September 2012 (UTC)[reply]
The term bimodal is frequently used if there are two most-prevalent values. Extensions to trimodal, etc. are obvious, but much less frequently used (usually lumped into the general category of "multimodal") - note that a set/distribution with a single mode would be classed as unimodal. Note that there wouldn't be a single value for the mode in that case. For a set/distribution without a mode, the use of Latin prefixes would mean the distribution would probably classed as "nonmodal" (as opposed to the greek-derived "amodal"), and if you were looking for a value of the mode, it would be undefined. - Note that having an undefined central tendency value isn't a problem. There are continuous distributions (like the Cauchy distribution) where the mean is not defined. -- 205.175.124.30 (talk) 01:59, 27 September 2012 (UTC)[reply]
  • Modes are mainly useful for characterizing mathematical distributions, such as a Gaussian etc. They are essentially useless for characterizing data unless you first fit a mathematical distribution to the data. Calculating modes directly from empirical data is almost always a waste of effort. Looie496 (talk) 02:34, 27 September 2012 (UTC)[reply]
A median can be mid-way between two values, but NOT a mode (unless Stu was thinking of making a rough estimate of the mode of a continuous unimodal distribution from a sample of values). There can be two different modes (bimodal, as mentioned above). Dbfirs 10:05, 27 September 2012 (UTC)[reply]
Yes, I'm thinking of an example where you plot incomes for a population of people and find the two most common incomes are $26,395 and $26,396. In a case like this, I think you would be justified in just calling the mode $26,395.50. StuRat (talk) 02:56, 28 September 2012 (UTC)[reply]
To enlarge slightly on my earlier point, the main place where modes come into play is in constructing histograms from data -- the mode is reported as the highest bin in the histogram. I repeat that calculating modes from raw data is almost always useless, unless the raw data is seriously discretized. Looie496 (talk) 03:03, 28 September 2012 (UTC)[reply]
Agreed on both points. The example given by the OP was presumably an artificial one at a very elementary level. Dbfirs 06:46, 28 September 2012 (UTC)[reply]

Uniformly bounded

[edit]

Show that is uniformly bounded in and , using the fact that converges.
Boundedness is clear to me; it is only uniform boundedess which is unclear to me. Widener (talk) 19:20, 27 September 2012 (UTC)[reply]

I think it means
I'd try something like:
Since the integral converges, the two limits will as well.
Let's find a bound for g(t):
sin/x is continuous over [1, inf] and so is g(t). g(t) converges to G; then from definition of limit: ; and since the function is continuous in [1,D] you can use the extreme value theorem, take K=max(|G|+1,E) and you've got:
Do the same for f(s), gives you a bound L;
M=K+L+pi , a bound for the whole function with Nx in [0,infinity]
since sin(-x)/(-x)=sin(x)/x the same values are valid for [-inf,0], so for all possible values xN... Ssscienccce (talk) 13:32, 29 September 2012 (UTC)[reply]

Sigmoid function between two points

[edit]

Hi, I'm wondering how to produce a sigmoid function that "starts" and "ends" at two points in a graph. So, for example, if I have p1=(2,2) and p2=(10,3), I would like to create a sigmoid function such that we pass through both these points, and the gradient is (or is nearly) 0 at each point, and the gradient is maximal exactly half-way between the points. Thanks! — Sam 63.138.152.135 (talk) 19:27, 27 September 2012 (UTC)[reply]

See Sigmoid function. Choose your base function (eg y = 1 / 1 + e^-x) and scale and offset it to go through your points. That particular function is a problem in that it doesn't reach the unscaled limits of 0 and 1 until -/+ infinity. At -/+ infinity you get a slope of 0, but it can't be scaled. You could choose a point close to the limit and say the tolerance is good enough or you could determine some finite exact points and scale those for a slope of only almost zero. Alternatively you choose a different function - there are many that have that sort of shape, but whether any have slope 0 at finite x I don't know. -- SGBailey (talk) 21:49, 27 September 2012 (UTC)[reply]
If you need to do it exactly, use spline interpolation with a cubic spline -- see Spline interpolation#Algorithm to find the interpolating cubic spline for the formula. Looie496 (talk) 22:18, 27 September 2012 (UTC)[reply]