Jump to content

User:SBlomaard/reinforced rubber

From Wikipedia, the free encyclopedia

Reinforced Rubber

[edit]

Although seldomly shared under this name, one of the largest groups of composite materials worldwide is that of the reinforced rubber products. Familiar examples are automobile tyres, hoses and conveyor belts.


Photo of fibre reinforcement structure on complex shaped rubber products by TANIQ

Composite Reinforced Structure
Reinforced rubber products combine a rubber matrix and a reinforcing material, so high strength to flexibility ratios can be achieved. The reinforcing material, usually a kind of fibre, provides the strength and stiffness. The rubber matrix, with low strength and stiffness, provides air-fluid tightness and supports the reinforcing materials to maintain their relative positions. These positions are of great importance because they influence the resulting mechanical properties.

Optimal Loading Condition
A composite structure where all fibres are loaded equally everywhere when pressurized, is called an isotropic structure and the type of loading is named an isotensoidal loading. To meet the isotensoidal concept the structure geometry must have an isotensoid meridian profile and the fibres must be positioned following geodesic paths. A geodesic path connects two arbitrary points on a continuous surface by means of the shortest possible way.

Straight Rubber Hoses
To achieve optimal loading in a straight rubber hose the fibres must be positioned under an angle of approximately 54.7 angular degrees, also reffered to as the magic angle. In this situation the fibres are only loaded on tensile strength so they can use 100% of their strength to take up the forces acting on the hose due to the internal pressure. (The magic angle for cylindrical shapes of 54.7 angular degrees is based on calculations in which the influence of the matrix material is neglected. Therefore, depending on the stiffness of the rubber material used, the actual neutral angle can vary a few degrees from the magic angle.)


Illustration 1. Fibre reinforced straight hose with a 57.4 degrees reinforcement angle.

Illustration 2. Reinforced garden hoses



When the fibres of the reinforcement structure are placed under angles larger than 54.7 angular degrees, the fibres want to relocate to their optimal path when pressurized. This means that the fibres will re-orientate themselves until they have reached their force equilibrium. In this case this will lead to an increase in length and a decrease in diameter. With angles smaller than 54.7 degrees the opposite will occur. A product which makes use of this principle is a pneumatic muscle.



Reinforcement of Complex Shaped Rubber Products


For a cylinder with a constant diameter the reinforcement angle is constant as well and is 54.7º. This also known as the magic angle or neutral angle. The neutral angle is the angle where a wound structure is in equilibrium. For a cylinder this is 54.7º, but for a more complex shape like a bellow which has a varying radius over the length of the product, this neutral angle is different for each radius. In other words, for complex shapes there is not one magic angle but the fibres follow a geodesic path with angles varying with the change in radius. To obtain a reinforcement structure with isotensoidal loading the geometry of the complex shape must follow an isotensoid meridian profile.

Reinforcement Application Technology
The fibre reinforcement can be applied on the rubber products with different processes. For straight hoses the most used processes are braiding, spiralling, knitting and wrapping. The first three processes have in common that multiple strands of fibres are applied to the product simultaniously on a predetermined pattern in an automated process. The fourth process comprises manual or semi-automated wrapping of rubber sheets reinforced with fabric plies. For the reinforcement of complex shaped rubber products like bellows most manufacturers use these fabric reinforced rubber sheets. These sheets are made by calendering of rubber onto pre-woven fabric plies. The products are manufactured by wrapping (mostly manually) these sheets around a mandrel until enough rubber and reinforcement is applied. However, the disadvantage of using these sheets is that it is impossible to control the positioning of the individual fibres of the fabric when applied on complex shapes. Therefore no geodesic paths can be achieved and therefore also no isotensoid loading is possible. To obtain isotensoide loading on a complex shape, the shape must have an isotensoideal profile and geodesic positioning of the fibre structure is required. This can be achieved by using automated winding processes like filament winding or spiralling.



References

[edit]

1. Koussios S, Nooij SM, Bergsma OK. Pressurised structures & hoses: improved structural performance and flexibility through optimal fibre reinforcement.


[edit]

·Reinforcement of complex shaped rubber products