Robust Header Compression

Robust Header Compression (ROHC) is a standardized method to compress the IP, UDP, UDP-Lite, RTP, and TCP headers of Internet packets.

The need for header compression

In streaming applications, the overhead of IP, UDP, and RTP is 40 bytes for IPv4, or 60 bytes for IPv6. For VoIP, this corresponds to around 60% of the total amount of data sent. Such large overheads may be tolerable in local wired links where capacity is often not an issue, but are excessive for wide area networks and wireless systems where bandwidth is scarce.^[1]

ROHC compresses these 40 bytes or 60 bytes of overhead typically into only one or three bytes, by placing a compressor before the link that has limited capacity, and a decompressor after that link. The compressor converts the large overhead to only a few bytes, while the decompressor does the opposite.

The ROHC compression scheme differs from other compression schemes, such as IETF RFC 1144 and RFC 2508, by the fact that it performs well over links where the packet loss rate is high, such as wireless links.

Main ROHC compression principles

The ROHC protocol takes advantage of information redundancy in the headers of the following:

one single network packet (e.g. the payload lengths in IP and UDP headers)
several network packets that belong to one single stream (e.g. the IP addresses)

Redundant information is transmitted in the first packets only. The next packets contain variable information, e.g. identifiers or sequence numbers. These fields are transmitted in a compressed form to save more bits.

For better performance, the packets are classified into streams before being compressed. This classification takes advantage of inter-packet redundancy. The classification algorithm is not defined by the ROHC protocol itself but left to the equipment vendor's implementation. Once a stream of packets is classified, it is compressed according to the compression profile that fits best. A compression profile defines the way to compress the different fields in the network headers. Several compression profiles are available, including the following:

Uncompressed
IP-only
UDP/IP
UDP-Lite/IP
ESP/IP
RTP/UDP/IP
RTP/UDP-Lite/IP
TCP/IP

Modes of operation

According to RFC 3095, the ROHC scheme has three modes of operation, as follows:

the Unidirectional mode (U-mode)
the Bidirectional Optimistic mode (O-mode)
the Bidirectional Reliable mode (R-mode)

Both the compressor and the decompressor start in U-mode. They may then transition to O-mode if a usable return link is available, and the decompressor sends a positive acknowledgement, with O-mode specified, to the compressor. The transition to R-mode is achieved in the same way.

Unidirectional Mode (U-Mode)

In the Unidirectional mode of operation, packets are only sent in one direction: from compressor to decompressor. This mode therefore makes ROHC usable over links where a return path from decompressor to compressor is unavailable or undesirable. In order to handle potential decompression errors, the compressor sends periodic refreshes of the stream context to the decompressor.

Bidirectional Optimistic Mode (O-Mode)

The Bidirectional Optimistic mode is similar to the Unidirectional mode, except that a feedback channel is used to send error recovery requests and (optionally) acknowledgments of significant context updates from the decompressor to compressor. The O-mode aims to maximize compression efficiency and aims for sparse usage of the feedback channel.

Bidirectional Reliable Mode (R-Mode)

The Bidirectional Reliable mode differs in many ways from the previous two modes. The most important differences are a more intensive usage of the feedback channel, and a stricter logic at both the compressor and the decompressor that prevents loss of context synchronization between compressor and decompressor, except for very high residual bit error rates.

Compressor/decompressor states

The notion of compressor/decompressor states is orthogonal to the operational modes. Whatever the mode is, both the compressor and the decompressor work in one of their three states. They are basically finite state machines. Every incoming packet may cause the compressor/decompressor to change its internal state. Every state refers to a defined behaviour and compression level.

The ROHC algorithm is similar to video compression, in that a base frame and then several difference frames are sent to represent an IP packet flow. This has the advantage of allowing ROHC to survive many packet losses in its highest compression state, as long as the base frames are not lost.

Compressor states

The compressor's state machine defines the following three states:

Initialization and Refresh (IR) state
First Order (FO) state
Second Order (SO) state

Operations in the different compressor states

In Initialization and Refresh (IR) state, the compressor has just been created or reset, and full packet headers are sent. In First-Order (FO) state, the compressor has detected and stored the static fields (such as IP addresses and port numbers) on both sides of the connection. The compressor is also sending dynamic packet field differences in FO state. Thus, FO state is essentially static and pseudo-dynamic compression. In Second-Order (SO) state, the compressor is suppressing all dynamic fields such as RTP sequence numbers, and sending only a logical sequence number and partial checksum to cause the other side to predictively generate and verify the headers of the next expected packet. In general, FO state compresses all static fields and most dynamic fields. SO state is compressing all dynamic fields predictively using a sequence number and checksum.

Transitions between compressor states

Transitions between the above states occur when the compressor:

compresses a packet that contains too many variations
receives a positive/negative feedback from the decompressor
periodically refreshes the context

Second-Order ROHC headers – 1-byte headers

A typical ROHC implementation will aim to get the terminal into Second-Order state, where a 1-byte ROHC header can be substituted for the 40-byte IPv4/UDP/RTP or the 60-byte IPv6/UDP/RTP (i.e. VoIP) header. In this state, the 8-bit ROHC header contains three fields:

a 1-bit packet-type flag (set to '1' only for longer ROHC headers)
a 4-bit sequence number (with a range of −1 ... +14 packets from the base frame)
a 3-bit CRC

Decompressor states

The decompressor's state machine defines the following three states:

No Context State
Static Context State
Full Context State

Transitions between the above states occur when the decompressor:

successfully decompresses a packet
fails to decompress several packets

Robustness

The size of the sequence number (SN) field governs the number of packets that ROHC can lose before the compressor must be reset to continue. The W-LSB algorithm is used to compress the SN in a robust way. The size of the sequence number in 1 and 2 byte ROHC packets is either 4 bits ( −1/+14 frame offset ), or 6 bits ( −1/+62 frame offset ), respectively, so ROHC can tolerate at most 62 lost frames with a 1-2 byte header.

Additional compression profiles

The RFC 3095 defines a generic compression mechanism. It may be extended by defining new compression profiles dedicated to specific protocol headers. New RFCs were published to compress new protocols:

The RFC 3843 defines a compression profile for IP headers or IP tunnels.
The RFC 4019 defines a compression profile for UDP-Lite/IP and RTP/UDP-Lite/IP headers.
The RFC 6846 defines a compression profile for TCP/IP headers.

Newer ROHC RFCs

There have been two new RFCs published RFC 4995 and RFC 5225 to address the confusion some have encountered when attempting to interpret and implement ROHC. The first document defines a ROHC framework, while the second defines newer versions of the established ROHC profiles.

References

^ Michael Dosch and Steve Church. "VoIP In The Broadcast Studio". Axia Audio. Archived from the original on 2011-10-07. Retrieved 2011-06-21.

External links

Official charter of the ROHC IETF working group
RFC 3095 - "ROHC Framework and four profiles: RTP, UDP, ESP, and uncompressed"
RFC 3759 - "ROHC Terminology and Channel Mapping Examples"
RFC 4815 - "Corrections and Clarifications to RFC 3095"
RFC 4995 - "The RObust Header Compression (ROHC) Framework" (obsoleted by RFC 5795)
RFC 4996 - "RObust Header Compression (ROHC): A Profile for TCP/IP (ROHC-TCP)" (obsoleted by RFC 6846)
RFC 4997 - "Formal Notation for ROHC"
RFC 5225 - "RObust Header Compression Version 2 (ROHCv2): Profiles for RTP, UDP, IP, ESP and UDP-Lite". Second version of the profiles found in RFC 3095, RFC 3843 and RFC 4019. It supersedes their definition, but does not obsolete them.
RFC 5795 - "The RObust Header Compression (ROHC) Framework" (obsoletes RFC 4995)
RFC 6846 - "RObust Header Compression (ROHC): A Profile for TCP/IP (ROHC-TCP)" (obsoletes RFC 4996)
A free implementation of ROHC on sourceforge.net
A free and efficient library implementing the ROHC standard

[1] Michael Dosch and Steve Church. "VoIP In The Broadcast Studio". Axia Audio. Archived from the original on 2011-10-07. Retrieved 2011-06-21.

[1]