Module:Location map/data/Australia Queensland/doc

This is a documentation subpage for Module:Location map/data/Australia Queensland.
It may contain usage information, categories and other content that is not part of the original module page.

This Lua module is used on approximately 6,100 pages and changes may be widely noticed. Test changes in the module's /sandbox or /testcases subpages, or in your own module sandbox. Consider discussing changes on the talk page before implementing them.

Location map of Queensland
border coordinates
name	Queensland
	-9
	137.5	←↕→	154
	-29.5
map center	19°15′S 145°45′E / 19.25°S 145.75°E / -19.25; 145.75
image	`Australia Queensland location map.svg`

image1	`Australia Queensland relief location map.jpg`

image2	`Australia Queensland location map blank.svg`

Module:Location map/data/Australia Queensland is a location map definition used to overlay markers and labels on an equirectangular projection map of Queensland. The markers are placed by latitude and longitude coordinates on the default map or a similar map image.

Usage

These definitions are used by the following templates when invoked with parameter "Australia Queensland":

{{Location map|Australia Queensland |...}}
{{Location map many|Australia Queensland |...}}
{{Location map+|Australia Queensland |...}}
{{Location map~|Australia Queensland |...}}

Map definition

name = Queensland
Name used in the default map caption

image = Australia Queensland location map.svg
The default map image, without "Image:" or "File:"
image1 = Australia Queensland relief location map.jpg
An alternative map image, usually a relief map, which can be displayed via the relief or AlternativeMap parameters
image2 = Australia Queensland location map blank.svg
Alternative map image which can be displayed via the AlternativeMap parameter
top = -9
Latitude at top edge of map, in decimal degrees

bottom = -29.5
Latitude at bottom edge of map, in decimal degrees

left = 137.5
Longitude at left edge of map, in decimal degrees

right = 154
Longitude at right edge of map, in decimal degrees

Alternative map

The {{Location map}}, {{Location map many}}, and {{Location map+}} templates have parameters to specify an alternative map image. The map displayed as image1 can be used with the relief or AlternativeMap parameters. The map displayed as image2 can be used with the AlternativeMap parameter. Examples may be found below or in the following:

Precision

Longitude: from West to East this map definition covers 16.5 degrees.

At an image width of 200 pixels, that is 0.0825 degrees per pixel.
At an image width of 1000 pixels, that is 0.0165 degrees per pixel.

Latitude: from North to South this map definition covers 20.5 degrees.

At an image height of 200 pixels, that is 0.1025 degrees per pixel.
At an image height of 1000 pixels, that is 0.0205 degrees per pixel.

Examples using location map templates

Location map, using default map (image)

Brisbane

Brisbane (Queensland)

{{Location map | Australia Queensland
| width = 200
| label = Brisbane
| lat_deg = 27  | lat_min = 28 | lat_sec = 04 | lat_dir = S
| lon_deg = 153 | lon_min = 01 | lon_sec = 40 | lon_dir = E
}}

Location map many, using relief map (image1)

Horn Island

Goondiwindi

Camooweal

Hervey Bay

class=notpageimage|

Locations in Queensland

{{Location map many | Australia Queensland
| relief   = yes
| width    = 200
| caption  = Locations in Queensland
| lat1 = -10.60 | long1 = 142.28 | label1 = Horn Island
| lat2 = -28.55 | long2 = 150.32 | label2 = Goondiwindi
| lat3 = -19.92 | long3 = 138.12 | label3 = Camooweal
| lat4 = -25.28 | long4 = 152.87 | label4 = Hervey Bay
}}

Location map+, using AlternativeMap