Jump to content

Wiener–Hopf method

From Wikipedia, the free encyclopedia
(Redirected from Wiener-Hopf factorization)

The Wiener–Hopf method is a mathematical technique widely used in applied mathematics. It was initially developed by Norbert Wiener and Eberhard Hopf as a method to solve systems of integral equations, but has found wider use in solving two-dimensional partial differential equations with mixed boundary conditions on the same boundary. In general, the method works by exploiting the complex-analytical properties of transformed functions. Typically, the standard Fourier transform is used, but examples exist using other transforms, such as the Mellin transform.

In general, the governing equations and boundary conditions are transformed and these transforms are used to define a pair of complex functions (typically denoted with '+' and '−' subscripts) which are respectively analytic in the upper and lower halves of the complex plane, and have growth no faster than polynomials in these regions. These two functions will also coincide on some region of the complex plane, typically, a thin strip containing the real line. Analytic continuation guarantees that these two functions define a single function analytic in the entire complex plane, and Liouville's theorem implies that this function is an unknown polynomial, which is often zero or constant. Analysis of the conditions at the edges and corners of the boundary allows one to determine the degree of this polynomial.

Wiener–Hopf decomposition

[edit]

The fundamental equation that appears in the Wiener-Hopf method is of the form

where , , are known holomorphic functions, the functions , are unknown and the equation holds in a strip in the complex plane. Finding , is what's called the Wiener-Hopf problem.[1]

The key step in many Wiener–Hopf problems is to decompose an arbitrary function into two functions with the desired properties outlined above. In general, this can be done by writing

and

where the contours and are parallel to the real line, but pass above and below the point , respectively.[2]

Similarly, arbitrary scalar functions may be decomposed into a product of +/− functions, i.e. , by first taking the logarithm, and then performing a sum decomposition. Product decompositions of matrix functions (which occur in coupled multi-modal systems such as elastic waves) are considerably more problematic since the logarithm is not well defined, and any decomposition might be expected to be non-commutative. A small subclass of commutative decompositions were obtained by Khrapkov, and various approximate methods have also been developed.[citation needed]

Example

[edit]

Consider the linear partial differential equation

where is a linear operator which contains derivatives with respect to x and y, subject to the mixed conditions on y = 0, for some prescribed function g(x),

and decay at infinity i.e. f → 0 as .

Taking a Fourier transform with respect to x results in the following ordinary differential equation

where is a linear operator containing y derivatives only, P(k,y) is a known function of y and k and

If a particular solution of this ordinary differential equation which satisfies the necessary decay at infinity is denoted F(k,y), a general solution can be written as

where C(k) is an unknown function to be determined by the boundary conditions on y=0.

The key idea is to split into two separate functions, and which are analytic in the lower- and upper-halves of the complex plane, respectively,

The boundary conditions then give

and, on taking derivatives with respect to ,

Eliminating yields

where

Now can be decomposed into the product of functions and which are analytic in the upper and lower half-planes respectively.

To be precise, where

(Note that this sometimes involves scaling so that it tends to as .) We also decompose into the sum of two functions and which are analytic in the lower and upper half-planes respectively, i.e.,

This can be done in the same way that we factorised Consequently,

Now, as the left-hand side of the above equation is analytic in the lower half-plane, whilst the right-hand side is analytic in the upper half-plane, analytic continuation guarantees existence of an entire function which coincides with the left- or right-hand sides in their respective half-planes. Furthermore, since it can be shown that the functions on either side of the above equation decay at large k, an application of Liouville's theorem shows that this entire function is identically zero, therefore

and so

See also

[edit]

Notes

[edit]
  1. ^ Noble 1958, §4.2.
  2. ^ Noble 1958, Chapter 1.

References

[edit]
  • "Category:Wiener-Hopf - WikiWaves". wikiwaves.org. Retrieved 2020-05-19.
  • "Wiener-Hopf method", Encyclopedia of Mathematics, EMS Press, 2001 [1994]
  • Fornberg, Bengt. Complex variables and analytic functions : an illustrated introduction. Piret, Cécile. Philadelphia. ISBN 978-1-61197-597-0. OCLC 1124781689.
  • Noble, Ben (1958). Methods Based on the Wiener-Hopf Technique for the Solution of Partial Differential Equations. New York, N.Y: Taylor & Francis US. ISBN 978-0-8284-0332-0.